• SOR-201 CATV & Satellite Optical Receiver
  • Model Number: SOR-201 CATV & Satellite Optical Receiver
  • Brand: softel
  • MOQ: 1
 


I. Features                    

With high sensitivity optical detector.

It is an embodiment of high-tech in CATV and L-band satellite fiber linking products

It can be received in an optical fiber with 47~2600MHz satellite and catv digital and analog signals.

Simple installation; It is convenient for user to install.

Input power from +0~-13dBm.

It has a good electromagnetic interference resistance ability.

High performance but low price.

II. Parameters

Optical

Working Wavelength(nm)

1290~1600

Input range(dBm)

-13~0

Optical Return Loss(dB)

≥45

Fiber Connector

SC/APC

RF

Frequency(MHz)

47~862

Unflatness(dB)

±1.5

Output Level(dBuV)

66~86@0dBm

Manual Gain Range(dB)

0~20±1

Output Return Loss(dB)

≥16

Output Impedance(Ω

75

No. of output port

2

RF connector

F-5(Imperial)

Link

CTB(dB)

≥62@0dBm

CSO(dB)

≥63@0dBm

CNR(dB)

  ≥50@0dBm

Test Condition:

60个 (PAL-D)channels, Optical input=0dBm, 3 steps EDFA 在噪Noise figure =5dB, distance 65Km, OMI 3.5%。

SAT-IF

Frequency(MHz)

950~2600

Output(dBm)

-50~-30

Unflatness(dB)

±1.5dB

IMD

-40dBc

Output Impedance(Ω

75

General

Power supply(V)

12 DC

Power Consumption(W)

≤4

Working Temp

0  50

Storage Temp

-20~85℃

Humidity

20  85%

IV. Operation Manual 

Light

Classification

Color

Condition

Light meaning

STAT

Power

 

 

Red/Green

ON

Powered

Off

No power

Optical Light

Green On

Fiber In≥-12dBm

Red On

Fiber<-12dBm or No input

 

 

Fiber

Types

Classification

Remarks

DC IN

Power supply

Power Supply Input

DC12v

OPT IN

Fiber Port

Optical Input

1310nm/1550nm Input

OUT_1、OUT_2

RF Port

RF Output

Connect to client

ATT

Level adjustment

Screw

Manual Gain range 0~20±1

v. Warranty TermS

SOR-201 Series Receiver are covered by one YEAR Limited Warranty, which starts from the initial date of your purchase. We provide its customer whole-life technical supports. If warranty is expired, repair service only charges parts (if required). In the event that a unit must be returned for service, before returning the unit, please be advised that:

 

1. Warranty mark pasted on the housing of unit must be in good conditions.

2. A clear and readable material describes model number, serial number and troubles should be offered.

3. Please pack the unit in its original container. If the original container is no longer available, please pack the unit in at least 3 inches of shock absorbing material.

4. Returned unit(s) must be prepaid and insured. COD and freight collect can not be acceptable.

 

NOTE: we do not assume responsibility for damage caused by improper packing of returned unit(s).

 

The following situation is not covered by warranty:

1. The unit fails to perform because of operators’ faults.

2. Warranty mark is modified, damaged and/or removed.

3. Damage caused by Force Majeure.

4. The unit has been unauthorized alteration and/or repaired.

5. Other troubles caused by operators’ faults.

V. Common Problem Solution

1.The power light off after connect the power supply

Reason:

Power supply not connected probably

The power supply fault

           Solution:    1. Check the connection

Change power adaptor

 

2.The optical IN Light Red

 

  Reason:    1. Fiber input -12dBm or no optical Input

2. The fiber connector loose

             3. The fiber connector dirty

  Solution:   1. Check the input

2. Check the connection

3. Clean the fiber connector